Technical specifications for IC660EBD110
Brand GE Intelligent Platform /GE Fanuc
Series Genius I-O
Manufacturer GE Fanuc/Emerson Automation
Part number IC660EBD110
Series block I/O
Part number IC660EBD110
Product line Genius I/O
Product description Electronic assembly
Product Type Electronic Assembly
Compatible module IC660BBD110 sixteen (16) input channels
Size 8.83x3.50x3.94 inches
Compatible terminal base IC660TBD110
Weight 4 pounds
Nominal input voltage 115 volts AC
Input to ground isolation 1500 volts
Input voltage range 93-132 VAC
Input current one 5
The IC660EBD110 is an electronic component assembly that is a component of the IC660BBD110 sixteen (16) point, 93-132 VAC discrete input module. The electronics component was previously manufactured by GE Fanuc Automation, but was recently acquired by Emerson Automation. As an electronic component, this component hosts the necessary circuits to achieve discrete input functions. The IC660EBD110 specifically hosts voltage sensing circuits, resistor/capacitor networks, and isolation circuits for input and output. It is paired with a terminal base that provides an end point for the input signal. The terminal base compatible with this electronic component is IC660TBD110. The IC660EBD110 has sixteen (16) discrete input channels and can accept input signal voltage ranges of 93-132 VAC and 47-63 Hz. The module's ground or serial bus isolated input is rated at 1500 V. This electronic component is capable of detecting input open and short routes, which are reported to the CPU and indicated locally via the Unit OK LED. In addition, the electronic assembly has an I/ O-enabled LED and 16 separate leds representing each input channel. The typical processing time for the input channel is 1 ms, and configured filter times such as 10 to 100 ms increase latency and can be configured in 10 ms increments. IC660EBD110 operating temperature is 0 to 60 degrees Celsius; Storage temperature -40 to 100 degrees Celsius; Relative humidity is 5-95%, no condensation, and operating vibration is 5-10 Hz, 2 inches or 5.088 displacement. When there is no power supply in the device, an electronic component must be installed because this component does not support live removal and insertion (RIUP).
The IC660EBD110 Electronic component assembly is an electronic component assembly with 16 circuits that are inputs only, manufactured by GE Fanuc as part of the Genius I/O device family. It operates in a voltage range of 93 to 132 volts AC, with a maximum heat dissipation rating of 28 watts when all 16 inputs are energized and full current is applied. The frequency range of the electronic component components is 47 to 63 Hz, and the power required for the electronic component components is only a maximum device current of 80 mA, and an additional maximum input circuit current of 200 mA. Other notable specifications include a 1500 volt input to ground isolation rating, a 5 amp terminal board rating, and an LED on each circuit to display the input status on the logical side. The GE Fanuc IC660EBD110 electronic assembly weighs approximately 1.8 kg and measures 8.83 x 3.50 x 3.94 inches. It also has an operating temperature range of 0 to 60 degrees Celsius and a storage temperature range of -40 to 100 degrees Celsius, as well as a non-condensing tolerable humidity range of 5 to 95 percent. The IC660EBD110 electronic component assembly has a resistive input circuit with a resistive load sufficient to activate the 2-wire approach switchgear. The module has an input resistance of 11.6 kiloohms and provides a preload current of 9.9 mA at a rated voltage of 115 volts. Each circuit of the IC660EBD110 electronic component assembly has its own LED indicator that indicates the presence of an on and off threshold voltage. The electronic component uses 16 input references, the value of which is 1, indicating that the input is equal to or higher than the configured threshold voltage.
